0–9
- 555 timer
- A timer chip first sold in 1972 and still everywhere: with two resistors and a capacitor it blinks, beeps or keeps time.More in Build a 555 LED blinker
A
- Anode
- The positive end of a diode or LED, where current goes in. On an LED it's the longer lead.More in Plan a perfboard layout
- Astable
- A circuit that never settles but flips between high and low by itself, forever: how a 555 blinks an LED.More in Build a 555 LED blinker
- AWG (American Wire Gauge)
- Wire size by number: the smaller the number, the thicker the wire. 22 AWG is about 0.64 mm across, 30 AWG about 0.25 mm.More in Wire a perfboard
B
- Breadboard
- A plastic block of spring clips for trying a circuit out without soldering. Great for experiments, no home for a finished circuit.More in Perfboard, stripboard or breadboard?
- Breadboard-style protoboard
- A solderable board with its pads joined in a breadboard's pattern, so a breadboard circuit moves across part for part.More in Perfboard, stripboard or breadboard?
- Bulk capacitor
- A larger capacitor, say 10 to 100 µF, where power enters the board, steadying the supply for the whole circuit.More in Plan a perfboard layout
- Bus wire
- Bare tinned copper wire laid along a row of pads on the copper side, usually for the power rails.More in Wire a perfboard
C
- Cathode
- The negative end of a diode or LED, where current comes out: marked by the band on a diode and the flat side of an LED.More in Plan a perfboard layout
- Cold joint
- A dull, lumpy joint where the solder never properly melted onto the metal. It may work for now, but it's unreliable: reheat it.More in How to solder (and fix bad joints)
- Component side
- The face of the board the parts sit on. The other face is the copper side.More in Wire a perfboard
- Continuity mode
- The multimeter setting that beeps when two points are connected: the quickest way to check a joint or a wire.More in Test and debug your board
- Copper side
- The face of the board with the copper pads or strips, where the leads poke through and get soldered. Also called the solder side.More in Wire a perfboard
- Current limit
- A bench power supply's ceiling on current. Set low for a first power-up, it stops a short from doing damage.More in Test and debug your board
- Cut (track cut)
- A break in a stripboard strip, made at a hole or between two holes, so one strip can carry two different connections.More in Stripboard (Veroboard) layout
D
- Decoupling capacitor
- A 100 nF capacitor right across a chip's power pins, supplying the sudden gulps of current the chip takes.More in Plan a perfboard layout
- Desoldering braid
- Fine copper braid, soaked in flux, that soaks up molten solder. Also called solder wick.More in How to solder (and fix bad joints)
- DIP (dual in-line package)
- A chip with two rows of pins 0.1 inch apart, made to go through holes. The 555 is an 8-pin DIP.More in Plan a perfboard layout
E
- Electrolytic capacitor
- A capacitor with a large value in a small can. It's polarized: the stripe on the can marks the negative lead.More in Plan a perfboard layout
- Enameled wire
- Fine copper wire coated in varnish, as used in coils. Solderable kinds lose their enamel on a hot iron. Also called magnet wire.More in Wire a perfboard
- ESD (electrostatic discharge)
- A static spark, often too small to feel, that can damage CMOS chips and MOSFETs.More in How to solder (and fix bad joints)
F
- Flux
- A cleaner that lets molten solder wet the metal instead of balling up. Electronics solder carries it in its core.More in Soldering tools and safety
- FR-2 and FR-4
- Board materials. FR-2 is cheap paper and resin, usually brown; FR-4 is stronger glass fiber in epoxy, usually green.More in Perfboard, stripboard or breadboard?
H
- Heat-shrink
- Plastic tubing that shrinks tight around a joint when heated, to insulate it. Slide it onto the wire before you solder.More in Wire a perfboard
J
- Jumper
- An insulated wire that hops over other connections, soldered through a hole at each end like a part.More in Wire a perfboard
L
- Lead
- A component's wire leg, the part that goes through the hole and gets soldered.More in How to solder (and fix bad joints)
- Lead-free solder
- Solder without lead, such as SAC305. It melts at about 217 °C, needs a hotter iron, and its joints look duller.More in Soldering tools and safety
- Link
- On stripboard, a short wire joining two strips.More in Stripboard (Veroboard) layout
M
- Mirror-image trap
- Planning a board from above but soldering it from below, where left and right are swapped.More in Plan a perfboard layout
N
- Net
- Everything that's connected together: one connection, however many pins it reaches.More in Plan a perfboard layout
P
- Pad
- The copper ring around a hole, which the solder bonds to.More in Perfboard, stripboard or breadboard?
- Perfboard
- A board with a grid of holes, each with its own copper pad and none of them joined: you make every connection yourself.More in Perfboard, stripboard or breadboard?
- Pin 1
- The pin a chip's numbering starts from, by the notch or dot. The rest count counterclockwise, seen from above.More in Plan a perfboard layout
- Pitch
- The spacing between holes or pins: 2.54 mm (0.1 inch) on almost every prototyping board.More in Perfboard, stripboard or breadboard?
- Plated-through hole
- A hole lined with copper that joins the pads on both faces, so solder fills it and grips the lead along its length.More in Perfboard, stripboard or breadboard?
- Polarized part
- A part that only works one way round: diodes, LEDs, electrolytic capacitors and chips.More in Plan a perfboard layout
R
- Rail
- A supply line, positive or ground, running along the board so every part can reach it with a short hop.More in Plan a perfboard layout
- Reverse-polarity diode
- A diode in series with the power input, so a battery connected the wrong way round can't do any damage.More in Plan a perfboard layout
- Rosin
- The classic flux, made from pine resin. Its smoke irritates the airways, so keep your face out of it.More in Soldering tools and safety
S
- Short circuit
- A connection that shouldn't be there, usually between the supply and ground. Find it before you power up.More in Test and debug your board
- Smoke test
- Engineers' joke name for the first power-up. The checks before it make it a non-event.More in Test and debug your board
- Socket
- A holder soldered in a chip's place, so the chip never meets the iron and can be swapped in seconds.More in Plan a perfboard layout
- Solder
- A soft alloy, melted to join metals. For electronics: a thin wire with flux in its core, about 0.8 mm across.More in Soldering tools and safety
- Solder bridge
- Solder joining two pads. Made on purpose it's a connection; made by accident it's a short.More in Wire a perfboard
- Solder side
- Another name for the copper side, where you solder.More in Plan a perfboard layout
- Spot-face cutter
- A hand tool with a cutting tip, twisted in a stripboard hole to cut the strip there.More in Stripboard (Veroboard) layout
- Strain relief
- Anchoring a wire before its joint, so a tug pulls on the board and not on the solder.More in Wire a perfboard
- Stripboard
- A board whose copper runs in strips, each joining a whole row of holes until you cut it.More in Stripboard (Veroboard) layout
- Surface-mount (SMD)
- Parts that sit on pads on top of a board instead of going through holes. On perfboard they go on adapter boards.More in Perfboard, stripboard or breadboard?
T
- Through-hole
- Parts whose leads go through holes in the board and are soldered on the other side: everything in these guides.More in How to solder (and fix bad joints)
- Tinning
- Coating a tip, wire or pad with a thin layer of solder, so it takes heat and joins quickly.More in How to solder (and fix bad joints)
V
- Veroboard
- The best-known brand of stripboard, often used as a name for any stripboard.More in Perfboard, stripboard or breadboard?
W
- Wetting
- Molten solder spreading over clean, hot metal and bonding with it, meeting it at a shallow angle: the sign of a good joint.More in How to solder (and fix bad joints)
- Wire-wrap wire
- Thin (30 AWG) insulated wire for dense signal wiring, run point to point on the copper side. Also called Kynar wire.More in Wire a perfboard
New here?
Seven short guides take you from choosing a board to powering up your first circuit, with a 555 blinker to build along the way.